Electric heating jacketed pot
keywords：
Category：
Product description
Shenlong electric heating jacketed pot is made of all-steel material, 304 stainless steel pot, safe and hygienic, double heating button control, timing temperature control with stirring function, widely used in food processing such as candy, pastry, beverage, fruit juice, jam, candied fruit, dairy and canned food And brewing, wine making, pharmaceutical and daily chemical industries, used for material melting, disinfection, heating, blanching, pre-cooking, preparation, boiling, steaming and concentration. At the same time, it is also suitable for large hotels, restaurants, hotels, guest houses, restaurants, industrial and mining enterprises, government agencies, and college canteens, as porridge, soup, dumplings, cooking and stew.
Instructions
1. Connect electricity and fill with heat-conducting oil: (1) One R3/4"x90 outer thread head and 3/4 threaded ball valve at 45 rear right of the outer bladder arc, for exhaust. The exhaust device is in the clamp The highest end of the sleeve, which is conducive to the discharge of gas during the heating process of the heat transfer oil to prevent the heat transfer oil from splashing out during the heating process. (2) The 200L pot is filled with L-
When the 0C320 heat transfer oil is 38kg (the quantity is for reference only), first lay the pot flat, fix the pot body with the locking device, and then connect the exhaust ball valve with the oil inlet device for use, and open the oil measuring hole for draining. Please pay attention to the oil measuring hole, and put the pot flat until the heat-conducting oil overflows from this hole. This hole is also the usual heat-conducting oil observation hole. Please fill it when the heat-conducting oil is less than this limit. (3) When the heat-conducting oil starts to heat up, remove the oil inlet oiler device and open the exhaust ball valve. After heating, close the exhaust ball, and shake the handle to turn the pot and pour the material. Use the oil inlet oiler device as an accessory. When refueling, connect the refueling device and the exhaust ball valve for use, and remove it after refueling. (4) After the pot, PT100 is used to measure the temperature of the heat transfer oil, and the set temperature is detected by the electric control box. When the set temperature is exceeded, it will not continue to heat, on the contrary, when it is lower than the set temperature, it will continue heating. (5) Install a 3/4 ball valve (high temperature resistant to 300℃) at the bottom of the oil drain device. This ball valve can be opened when the oil needs to be drained, which can make the oil drain more convenient.
2. Clean the pot and put in the materials. You should inject heat-conducting oil first, turn on the power, and turn off the power when the materials reach the required temperature and the predetermined heating time. The hand wheel can be turned to tilt the pot body for unloading. At this point, one job is completed.
3. Check the capacity of the heat transfer oil every time you perform an operation to avoid dry burning and damage to the equipment.
4. In order to ensure the cleanliness of the heat transfer oil, it should be replaced every 3 months
5. In order to keep it clean, it should be cleaned every time it is used.
6. Before using the tiltable jacketed pot, check whether the rotating part is well lubricated. Fill the oil cup with grease and inject a proper amount of grease into the bite of the worm gear and worm.
Instructions
1. Connect electricity and fill with heat-conducting oil: (1) One R3/4"x90 outer thread head and 3/4 threaded ball valve at 45 rear right of the outer bladder arc, for exhaust. The exhaust device is in the clamp The highest end of the sleeve, which is conducive to the discharge of gas during the heating process of the heat transfer oil to prevent the heat transfer oil from splashing out during the heating process. (2) The 200L pot is filled with L-
When the 0C320 heat transfer oil is 38kg (the quantity is for reference only), first lay the pot flat, fix the pot body with the locking device, and then connect the exhaust ball valve with the oil inlet device for use, and open the oil measuring hole for draining. Please pay attention to the oil measuring hole, and put the pot flat until the heat-conducting oil overflows from this hole. This hole is also the usual heat-conducting oil observation hole. Please fill it when the heat-conducting oil is less than this limit. (3) When the heat-conducting oil starts to heat up, remove the oil inlet oiler device and open the exhaust ball valve. After heating, close the exhaust ball, and shake the handle to turn the pot and pour the material. Use the oil inlet oiler device as an accessory. When refueling, connect the refueling device and the exhaust ball valve for use, and remove it after refueling. (4) After the pot, PT100 is used to measure the temperature of the heat transfer oil, and the set temperature is detected by the electric control box. When the set temperature is exceeded, it will not continue to heat, on the contrary, when it is lower than the set temperature, it will continue heating. (5) Install a 3/4 ball valve (high temperature resistant to 300℃) at the bottom of the oil drain device. This ball valve can be opened when the oil needs to be drained, which can make the oil drain more convenient.
2. Clean the pot and put in the materials. You should inject heat-conducting oil first, turn on the power, and turn off the power when the materials reach the required temperature and the predetermined heating time. The hand wheel can be turned to tilt the pot body for unloading. At this point, one job is completed.
3. Check the capacity of the heat transfer oil every time you perform an operation to avoid dry burning and damage to the equipment.
4. In order to ensure the cleanliness of the heat transfer oil, it should be replaced every 3 months
5. In order to keep it clean, it should be cleaned every time it is used.
6. Before using the tiltable jacketed pot, check whether the rotating part is well lubricated. Fill the oil cup with grease and inject a proper amount of grease into the bite of the worm gear and worm.
Related products
Welcome your message consultation
Mobile QR Code
CONTACT US
Tel：+86-536-6359986
Mr.wang：+86-15863278588
E-mail：zhuchengshenlong@163.com
Address: Changcheng Industrial Park, Zhucheng City, Shandong Province
Copyright © 2022 Zhucheng Shenlong machinery Factory